In Line Weld Repairs of Valve Defects

Variety of Valves Repaired

Extensively trained personnel using specially developed welding and machining equipment made repairs on a variety of valves from all the major OEMs. Most of the 50 repairs were on valves ranging in size from 12” to 24”. Twenty-three projects were repairs of code boundary valves. These repairs were performed following the guidelines of ASME Section I and National Board Inspection Code as well as Jurisdictional requirements. Twenty-seven-plus valves were part of the boiler external piping. These repairs were performed following the guidelines of ASME B31.1.

Valves manufactured for use in the power generation sector are produced under the American National Standards as outlined in ASME B16.34 and requirements placed on specific valves by the customer. This standard applies to new construction and covers pressure-temperature ratings, dimensions and tolerances, materials NDE (non-destructive examination) requirements, testing, marking of cast, forged and fabricated valves with flanged, threaded or welded ends.

The manufacturers are responsible for providing the purchaser with documentation that details their quality program compliance in the manufacturing of their products. The requirements for manufacturing may be less stringent than those required to repair valves placed in service.

NDE acceptance standards on new valves manufactured are found in ASME B16.34 Mandatory Appendix II for Magnetic Particle Examination and Mandatory Appendix III for Liquid Penetrant Examination. Both provide procedure and acceptance standards for castings and forgings and rolled wrought material.

These standards are far less restrictive than those of ASME Section I or ASME B31.1.

ASME Section I Repairs

Repair requirements of a valve are usually confined to the location of the valve in the boiler piping system of the power plant. If the valve to be repaired is located in the piping system–which is considered part of the boiler proper or part of the external boiler piping–it is declared to be inside the Boiler Code Boundary.

The Preamble to ASME Section I paragraphs 4, 5 & 7 provides the detailed information defining Code Boundary. Repairs to piping and valves within the Code Boundary are repaired using the requirements provided in ASME Section I, National Board Inspection Code (NBIC) and the jurisdiction of the repair. Most of the ASME Section I repairs can be segregated into three groups.

1. Valves requiring a seat or seats replaced
2. Removal and rewelding of Integral valve seats
3. Repair of cracks in the valve body or on the guide ribs or disc guides.

Valves with seats manufactured from A355-P22 (5A) material were replaced with like for like.

All seat rings were replaced using the following guidelines:

• All seat pockets were measured to ensure new seat fit.
• If dissimilar welding was performed on original seat, all old metal was removed and then acid etched to ensure complete removal. Rewelded with base metal and machined to size. NDE (Dry MT)(magnetic particle testing) of the new pocket.
• Minimum preheat 400o F
• Welding process machine GTAW (gas tungsten arc welding)
• WPS – 15E MN/MC GTAW-HT
• 035” ф dia Wire – Er90S-B9 GTAW
• Mn + Ni chemistry <1.0
• PWHT (post weld heat treatment) @ 1375o F – 2 hours soak time minimum
• Thermocouples and ceramic pads on ID seat area
• Final NDE (PT) (dye penetrant testing) and (VT) (visual testing)

The other 50% of the repairs were on integral seats in the valves.

Integral seat repairs use the following guidelines:

• Remove all the hardfacing and .080” – .100” of base metal.
• Insure all visible defects are removed
• NDE (PT) inspection of all repair areas
• Sketch and dimension all repair areas
• Preheat the valve to 400o F minimum. Note: 300o F for (P-4) material
• Weld excavated repair areas and undercut area with Er90S-B9 (Er80S-B2 for P-4 material)
• Profile all the repair areas and NDE dry (MT) on all P15E materials. Keep base material at 100o F. No moisture is allowed on “as welded” 15E materials. NOTE: PT or wet (MT) is allowed on all other low alloy materials.
• Re-establish 400o F [reheat
• Apply minimum of (2) layers of stellite 21
• Cool valve to below 175o F and visually inspect welds
• PWHT minimum hold 2 hours @ 1375o F per heat treat traveler. NOTE: PWHT temp 1250o F for P-4 material
• Profile the seat and guide ribs to OEM specifications
• Final NDE, PT to ASME Section I and VT to ASME B31.1
• An authorized inspector will review the weld data package and issuance of R-1 form and data plate as required.

ASME B31.1 Valve Repairs

According to this section, “All welding or brazing of pipes or items shall be performed by manufacturers or contractors authorized to use the appropriate symbol shown in Fig. PG-105-1 thru PT-105.3 of ASME Section I of the ASME Boiler and Pressure Vessel Code (B31.1 Chapter 1 100.1.2).”

The installer of external boiler piping jointed by welding or brazing is required to have a quality control system, meeting the requirements of Mandatory Appendix J of the ASME Section B31.1 Code.

The majority of the valves repaired under B31.1 have been parallel slide gate valves. The valve bodies have been A217-C12A material. The seat rings have been a mix of F91, P22 materials. As with the section I valves the defects have been the same: Seats cracking in the heat-affected zone on the body side of the body to seat ring weld and stellite breaking off the seat ring face and entering into the systems.

1. Removal of defect or reduce to acceptable size.
2. NDE of defect area either by PT or MT, acceptance criteria per Chapter V- 136.4.3 for MT and 136.4.4 for PT
3. Preheat of the base material as required in Chapter V-131 “Welding Preheat.”
4. Welding shall be performed by use of PQRs (procedure qualification records), WPSs (welding procedure specifications) and WPQs (welder performance qualifications) as outlined in Chapter V-127.5.
5. PWHT of repair as required by Chapter V-132 “PWHT Requirements.”
6. Final NDE of the repair as required in Chapter V-136.4 “Examination methods for welds and repairs.”

ASME B31.1 Chapter V

1. Visual Examination (VT) – 136.4.2
2. Magnetic Particle Examination (MT) – 136.4.3
3. Liquid Penetrant Examination (PT) – 136.4.4

All examinations must be performed by technicians certified to perform each non-destructive examination per ASME B31.1 Chapter V-136.3.2 “Qualifications of NDE personnel.”

Summary

• boiler unit number
• boiler manufacturer
• manufacturers’ serial numbers
• national board number
• jurisdiction number (if applicable)
• year built
• original code of construction
• system and location of valve being worked
• valve drawing
• valve identification
• valve year of manufacture

Once all the pertinent information is gathered, quality assurance and the welding departments begin the planning process:

• Initiate work travelers and weld data sheets.
• Identify WPS (wafer style pressure sensors) and welder performance qualifications.
• Create PWHT travelers and contact heat treat sub contractor.
• Identify NDE requirements and notify NDE subcontractor.
• Issue filler material and supporting documentation MTR/CMTRs.
• Notify authorized inspector (if required and establish AI hold points).
• Present weld traveler and data package to project manager for review.

Specialized machining and welding equipment has been developed for repairing each type of valve and their repairs. Equipment is staged and inspected on a similar valve mockup and tested before shipping to each project.

The “Recipe for Success” may seem simple, but care must be taken on each step to ensure the best possible result for each valve repair.

REFERENCES: ASME Boiler and Pressure Vessel Code Section I “Rules for – Construction of Power Boilers.”B31.1. “ASME Code for Pressure Piping.” B16.34 “Valves – Flanged, Threaded, and Welding End,” American Society of Mechanical Engineers, New York, NY. USA.

Joanna Button is quality assurance manager at CFM/VR-TESCO, LLC. Reach her at Jbutton@globalfield.net

Editor’s Note: Contents of this article were originally presented at the Valve Manufacturers Association Technical Seminar in March 2013, by Scott Smith, SVP & General Manager, and Roy Button, Welding Engineer & Specialty Welding (WDI) Division Manager.